*740008*
740008
© Allegion 2014
Printed in U.S.A.
740008 Rev. 02/14-c
Push Arm Installation
1a Install the header and door bracket using the appropriate template.
1b Using the appropriate chart, measure and cut the exact length required for the threaded rod. Threaded rod length is
determined by measuring the reveal dimension (in inches) from the surface of the door to which the arm is attached
to the back surface of the header. Using the horizontal scale (calibrated in inches and quarter inches), follow the
vertical line of the reveal dimension upwards until it intersects the slanted line. Reading to the left of the vertical scale
will determine the exact length (between centers of the turnbuckles) of threaded rod required. DO NOT CUT THE
THREADED ROD FROM THE END WITH THE HOLE!
L NOTE: The operator spindle is normally at the full breakout position (-90º). The arm must be attached to the spindle at the
full open position (+90º).
1c Turn on power to the operator and momentarily short the activation wires together. The spindle will begin to slowly
rotate to the open position. When the spindle stops rotating, momentarily short the activation wires together again.
Continue this process until the spindle has reached the full open position (+90º).
1d Once the spindle is at the full open position (+90º), wire nut the activation wires together.
1e Install the spindle adapter into the arm as required. (See appropriate template.)
1f Install the arm onto the spindle at the full open position (+90º) and tighten cap screw.
1g Screw the threaded rod into the turnbuckles.
1h Remove the wire nut from the activation wires.
1i Connect activation wires to activation device.
1j Test door operation.
1k If no further adjustments are needed, secure the arm by installing the washer and screw.
Models 9540, 9550, 9560
Push Arm & Link
Assembly
Installation Instructions
Installation Template Offset Pivoted or Butt Hinged Doors
FOR SURFACE APPLIED OPERATORS WITH PUSH ARMS
ON OFFSET PIVOTED OR BUTT HINGED DOORS
10" MAX. REVEAL POSSIBLE
WITH STANDARD LINK SUPPLIED
MINIMUM REVEAL
IS 1-1/8"
REVEAL DEPTH IN INCHES
0
15
14
13
12
11
10
9
8
7
6
5
S
E
C
O
N
D
A
R
Y
L
IN
K
L
E
N
G
T
H
IN
I
N
C
H
E
S
REVEAL DEPTH IN INCHES
25
24
23
22
21
20
19
18
17
16
15
S
E
C
O
N
D
A
R
Y
L
IN
K
L
E
N
G
T
H
IN
I
N
C
H
E
S
14
20" MAX. REVEAL POSSIBLE
WITH SPECIAL EXTENDED LINK
1 2 3 4 5 6 7 8 9 10
10
11
12 13 14 15 16
17 18
19
20
Installation Template 2 C\v” Center Pivoted Doors
FOR SURFACE APPLIED OPERATORS WITH PUSH ARMS
ON 2-3/4" CENTER PIVOTED DOORS
20" MAX. REVEAL POSSIBLE
WITH SPECIAL EXTENDED LINK
MIN. REVEAL IS 1"
REVEAL DEPTH IN INCHES
20
19
18
17
16
15
14
13
12
11
S
E
C
O
N
D
A
R
Y
L
I
N
K
L
E
N
G
T
H
I
N
I
N
C
H
E
S
REVEAL DEPTH IN INCHES
29
28
27
26
25
24
23
22
21
20
S
E
C
O
N
D
A
R
Y
L
I
N
K
L
E
N
G
T
H
I
N
I
N
C
H
E
S
19
18
17
0 1 2 3
4
5 6 7
8
10
11
12 13
14
15 16
17 18
19
20
98
8" MAX. REVEAL POSSIBLE
WITH STANDARD LINK SUPPLIED
Installation Template 3 C\v” Center Pivoted Doors
FOR SURFACE APPLIED OPERATORS WITH PUSH ARMS
ON 3-3/4" CENTER PIVOTED DOORS
S
E
C
O
N
D
A
R
Y
L
I
N
K
L
E
N
G
T
H
I
N
I
N
C
H
E
S
9" MAX. REVEAL POSSIBLE
WITH STANDARD LINK SUPPLIED
MIN. REVEAL IS 1"
REVEAL DEPTH IN INCHES
REVEAL DEPTH IN INCHES
20" MAX. REVEAL POSSIBLE
WITH SPECIAL EXTENDED LINK
S
E
C
O
N
D
A
R
Y
L
I
N
K
L
E
N
G
T
H
I
N
I
N
C
H
E
S
18
17
16
15
14
13
12
11
10
19
0 1 2 3
4
5 6 7 8 9
10
11
12 13 14
15
16
17 18
19
20
9
16
28
27
26
25
24
23
22
21
20
19
18
17
Customer Service
1-877-671-7011 www.allegion.com/us
