Product Code:
Product Name:
59401
ASSEMBLY INSTRUCTIONS
1. Use key to unlock lock on Collar Bracket.
2. Pull spring loaded release pin on side of Main Support tube, remove handle mechanism, and rotate bike
Support Arms into the UP position. Re-insert the handle mechanism. Pull out the spring loaded release
pin and push handle all the way down. Let the spring loaded pin go so that it fully engages the handle
mechanism.
3. Slide the Collar Bracket onto the bike carrier Main Support tube in orientation shown (see Diagram 1).
4. Attach Collar Bracket to Main Support tube using one (1) ½” x 3-1/4” lg. hex bolt, two (2) nylon flat
washers, and locknut installed through the “slotted” hole in Collar Bracket. Tighten locknut until it is snug
against the flat washers.
5. Attach Receiver piece to Collar Bracket using two (2) ½” x 3” hex bolts through the
½” diameter holes (closest to end of tube). (See Diagram 2)
Tighten Receiver piece bolts to 75 Lb.-Ft.
7. Lock Collar Bracket to Main Support tube so bike carrier is in the upright position.
1/2” x 3-1/4” Hex Bolt
Please read all instructions carefully before assembly, installation and/or use of this product.
2” Shank
½” Locknut
Diagram 1
Diagram 2
Diagram 3
Handle Mechanism
Release
Pin
4 Place Bike Carrier - Folding
1/2” x 3-1/4” Hex Bolt
½” Locknut
Nylon Washer
Product Code:
Product Name:
INSTRUCTIONS FOR FOLDING THE RACK:
1. To release the lock pin, pull spring pin and rotate 90 degrees.
2. Pull support tube firmly upwards until lower pin slides to the top of its slot.
(See Diagram 6)
3. Lower the tube slowly back until support tube rests on the stop plate.
NOTE: Do not drop or let the support tube fall freely. Make sure that your
hands and fingers are clear of the hinging area during this operation.
4. To restore the rack to the upright position, do reverse procedure.
5. Check periodically to insure you have a solid fit between the rack and the
mounting location
Diagram 6
LOADING INSTRUCTIONS:
1. Place the bike rack receiver into your receiver hitch. Fit rack as close to vehicle as possible.
2. For 2” hitch, secure rack with 5/8” hitch pin and clip.
3. The bikes are loaded onto the rack alternating each bike, with the anti-sway cradle being closest to the seat tube.
(See Diagram 5)
4. Secure the bikes by pulling the bungee straps over the top of the bike frame. The anti-sway straps wrap around the
seat tube prevent the bike from swaying.
5. Check the bungee straps periodically and after stopping to insure that they are still tight and that someone has not
released them. NOTE: Insure all locks are locked, that all pins are secured, and that all bungee straps are properly
attached prior to moving the vehicle. Failure to do so will void the warranty.
Diagram 4
Anti-Sway Cradle
Diagram 5
Install 5/8” Silent Hitch Pin and clip for 2” hitch
59401
Please read all instructions carefully before assembly, installation and/or use of this product.
4Place Bike Carrier - Folding
Product Code:
Product Name:
59401
IMPORTANT NOTES:
• This bicycle rack has been designed to carry four (4) bikes, as long as the maximum weight on the rack does
not exceed 45 kgs or 100 lb.
• This rack is designed for typical use and applications (on paved or smooth gravel roads). Do not use this rack
on a vehicle that will be driven on rough roads or where the rack (and bikes) will be subjected to significant or
constant jarring and/or shock, or any vehicle with very stiff springs that will transfer the load shocks directly to
the rack and the bikes.
• Proper fitting and installation of this carrier to your specific vehicle is critical, and is the owner’s sole
responsibility.
• Improper use of this product may result in damage to your rack, your vehicle, your bicycles, or even other
vehicles driving behind you (as a result of colliding with or trying to avoid fallen bicycles and/or the rack).
• ROLA™ racks are powder coated to help prevent rust. As with any metal equipment it is recommended that
you keep the rack clean and remove road salt and debris.
• When leaving them outside for extended periods of time the finish will lose its luster. It is recommended that
when not in use the rack is stored indoors.
• The rack won’t carry bikes with oblong frame tubes or unusually large frame sizes.
• Take care to add padding on any area of the bikes that touches another bike or any part of the vehicle.
Damage can and will happen (to your bikes and/or to the vehicle) if care is not taken during the loading and
transporting of your bikes, and padding used where necessary.
• Bicycle tires should be kept at least 6” away from the exhaust pipes of the vehicle. The high temperature
exhaust exiting from the exhaust pipes is hot enough to melt or damage tires. Keep all bike tires totally away
from the direct exhaust flow.
• Bikes fitted with large accessories (such as child carrying seat) will greatly increase the wind resistance
and therefore the pressure on the rack and all vehicle-mounting points. Reducing vehicle speed will reduce
the chance of any problems occurring because of this situation.
• After reading this manual, should you have any additional questions regarding the compatibility, fitting and/or
use of this rack, please call your nearest ROLA™ authorized retail dealer.
WARNING:
• DO NOT USE THIS BIKE CARRIER ON A TRAILER OR 5
th
WHEEL R.V.
• Improper mounting will void the rack warranty.
• Damage to bicycles or rack due to ground clearance problems are not covered by warranty.
Please read all instructions carefully before assembly, installation and/or use of this product.
4 Place Bike Carrier - Folding
Shop for quality Rola on our website.
On our website you can discover more about Bike Racks.
