Need help with your appliance?
Contact our customer service team
or visit our website for information
and tips on getting the most from
your appliance.
Australia | visit www.sunbeam.com.au
phone 1300 881 861
mail Units 5 & 6, 13 Lord Street,
Botany NSW 2019 Australia.
New Zealand | visit www.sunbeam.co.nz
phone 0800 786 232
mail Level 6, Building 5,
Central Park,
660–670 Great South Road,
Greenlane, Auckland.
Sunbeam Corporation Limited | ABN 45 000 006 771.
Sunbeam is a registered trade mark.
Sleep Express and Boost Technology are trade marks of Sunbeam Corporation.
Made under license of Australian Patent No. AU2013203697 (B2),
and New Zealand Patent No. NZ609279 (A)
Made in China to Sunbeam’s specification.
Due to minor changes in design or otherwise,
the product you buy may differ slightly from the one shown here.
Approved by the appropriate electrical regulatory authorities.
©Copyright Sunbeam 2017.
12/17
BL48_BL49_17EM1
CSH-LD1217-SUN175907
User Guide
DREAMLAND
ELECTRIC BLANKETS
Australia
www.sunbeam.com.au
1300 881 861
Units 5 & 6,
13 Lord Street,
Botany NSW 2019
Australia
N
ew Zealand
www.sunbeam.co.nz
0800 786 232
Level 6, Building 5,
Central Park,
660-670 Great South Road,
Greenlane, Auckland
New Zealand
Year
3 year
3 years
3
BLD5021
BLD5031
BLD5041
BLD5051
BLD5071
BLD5021 Dreamland Fitted Single Bed
BLD5031 Dreamland Fitted King Single Bed
BLD5041 Dreamland Fitted Double Bed
BLD5051 Dreamland Fitted Queen Bed
BLD5071 Dreamland Fitted King Bed
1
If you have any concerns regarding the performance and use of your appliance,
please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.
Ensure the above safety precautions are understood.
Contents
Sunbeam is very safety conscious when designing
and manufacturing consumer products, but it is
essential that the product user also exercise care
when using an electrical appliance. Listed below
are precautions which are essential for the safe
use of an electrical appliance:
• Read carefully and save all the instructions
provided with an appliance.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove
by grasping the plug - do not pull on the cord.
• Turn the power off and remove the plug
when the appliance is not in use and
before cleaning.
• Do not use your appliance with an extension
cord unless this cord has been checked
and tested by a qualified technician or
service person.
• Always use your appliance from a power
outlet of the voltage (A.C. only) marked
on the appliance.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure that
they do not play with the appliance.
• The temperature of accessible surfaces may be
high when the appliance is operating.
• Never leave an appliance unattended while
in use.
• Do not use an appliance for any purpose
other than its intended use.
• Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven.
• Do not place on top of any other appliance.
• Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
• Do not operate any electrical appliance with
a damaged cord or after the appliance has
been damaged in any manner. If damage is
suspected, return the appliance to the nearest
Sunbeam Appointed Service Centre
for examination, repair or adjustment.
• For additional protection, Sunbeam
recommend the use of a residual current
device (RCD) with a tripping current not
exceeding 30mA in the electrical circuit
supplying power to your appliances.
• Do not immerse the appliance in water
or any other liquid unless recommended.
• Appliances are not intended to be operated
by means of an external timer or separate
remote control system.
• This appliance is intended to be used in
household and similar applications such
as: staff kitchen areas in shops, offices and
other working environments; farm houses; by
clients in hotels, motels and other residential
type environments; bed and breakfast type
environments.
• Do not place heavy items on your bed when
the electric blanket is turned on.
• It is recommended that a qualified engineer
or registered person inspect the heated
blanket once it passes warranty period and
every 2 years thereafter.
Sunbeam’s Safety Precautions
BREKKY AND
BANQUET
User Guide
Need help with your appliance?
Contact our customer service team
or visit our website for information
and tips on getting the most from
your appliance.
Australia | visit www.sunbeam.com.au
phone 1300 881 861
mail Units 5 & 6, 13 Lord Street,
Botany NSW 2019 Australia.
New Zealand | visit www.sunbeam.co.nz
phone 0800 786 232
mail Level 6, Building 5,
Central Park,
660–670 Great South Road,
Greenlane, Auckland.
Sunbeam Corporation Limited | ABN 45 000 006 771
Sunbeam Corporation is a division of GUD Holdings Limited.
Sunbeam is a registered trademark.
‘Brekky and Banquet’ is a trademark of Sunbeam Corporation.
Made in China to Sunbeam’s specification.
Due to minor changes in design or otherwise,
the product you buy may differ slightly from the one shown here.
Approved by the appropriate electrical regulatory authorities.
©Copyright Sunbeam 2014.
9/14
PU6400
Australia
www.sunbeam.com.au
1300 881 861
Units 5 & 6,
13 Lord Street,
Botany NSW 2019
Australia
New Zealand
www.sunbeam.co.nz
0800 786 232
Level 6, Building 5,
Central Park,
660-670 Great South Road,
Greenlane, Auckland
New Zealand
Sunbeam’s Safety Precautions 1
Safety Precautions for your Electric Blanket 2
Features of your Dreamland electric blanket 3
Fitting your electric blanket 4
Using your electric blanket 5
Care and cleaning 7
Troubleshooting 8
32
Safety Precautions for your
Electric Blanket
• Do not use your electric blanket on or under a
waterbed.
• Do not use on an adjustable bed or futon.
• Do not switch the blanket on if moist or wet.
• Do not allow the blanket heating wires to lie over
the edge of the mattress.
• Do not place your power cord or connector under
any stress or strain. Never jam or bend the power
cord over a hard surface such as a bed frame.
The power cord should always remain free from
obstructions.
• Do not use pins, needles, safety pins or other
sharp items on your electric blanket.
• Do not dry clean your electric blanket.
• Use only as an underblanket.
• Examine periodically for signs of wear or damage
on the blanket cords. If there are such signs, or
the blanket has been misused, return it to an
authorised service agent for inspection.
• Each day check that the electric blanket is
smooth, flat and properly secured on the
mattress. Do not use if the blanket is folded,
rucked or creased.
• Only use your electric blanket with the controls
supplied or marked equivalent.
• Do not use with infants, infirm persons, or
persons insensitive to heat.
• Parents or guardians must preset the controls
for young children, unless the child has been
adequately instructed on how to operate the
control safely.
• Children under the age of three are not to use
this appliance due to their inability to react to
overheating.
• Turn the power off and remove the plug when the
appliance is not in use and before cleaning.
• This electric blanket is not intended for use in
hospitals.
• When storing the appliance, allow it to cool down
before folding.
• Do not crease the appliance by placing items on
top of it during storage.
• Should your appliance suffer a thermal or fuse
link rupture (normally identified when the
blanket stops heating) please return it to the
manufacturer or agent for repair or replacement.
• Heat settings 1-4 are for continuous or all night
use. If this appliance is slept on with the controls
set to a higher temperature, the user may suffer
skin burns or heat stroke.
If you have any concerns regarding the performance and use of your appliance,
please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.
Ensure the above safety precautions are understood.
Important instructions – retain for
future use.
Care Label Symbols
Attention
Instruction Booklet - Please read the instructions thoroughly before use
Features of your Dreamland
electric blanket
Dreamland Fitted electric blankets have the
following features:
Fitted blanket
Just like a fitted sheet, this electric blanket
has elasticised sides to keep it secure on the
mattress and make fitting easy.
Machine washable
For convenient care, this electric blanket
can be machine washed and may be tumble
dried. For instructions on how to launder
your electric blanket, see the Care and
cleaning section on page 7.
9 heat settings
The easy to use illuminated controls offer
a choice of heat settings from 1 to 9, so
you can select the perfect heat level for
preheating or all night use. The selected heat
setting is displayed on the LCD.
Digital timer control
The handy countdown timer switches the
electric blanket off automatically - after 3, 6
or 12 hours.
Extra foot warmth
This electric blanket provides extra warmth to
your feet while keeping the rest of your body
at a comfortable temperature.
Detachable controls
Remove the controls when laundering or
storing your electric blanket.
Dual controls
Double, Queen and King size blankets
have two control units providing individual
comfort.
Overheat protection
A safety mechanism within this electric
blanket automatically switches the blanket
off in the unlikely event of a fault.
Antibacterial Treatment
Ideal for asthma and allergy sufferers, this
electric blanket incorporates antibacterial
treatment into the polyester fibres, helping
to inhibit the growth of bacteria and mould.
This treatment ensures a fresher, more
hygienic blanket that lasts even when
washed regularly.
BLD5021 Single Bed
BLD5031 King Single Bed
BLD5041 Double Bed
BLD5051 Queen Bed
BLD5071 King Bed
54
Note: The heat pad is designed to fit within
the edges of your mattress (see Figure 3).
This ensures the best, smoothest and firm
fit of your blanket to the mattress. As the
blanket settles in to the fit of the bed, any fold
ridges should smooth out over time.
Place the electric blanket on your mattress
with the control sockets on the underside of
the blanket near the head of the bed
(see Figure 3). Ensure the heating wires do
not extend under the pillows.
A single or king single fitted electric blanket
can be turned over so that the control is on
the preferred side of the bed if desired.
Pull the elasticised skirt over the top corners
of the mattress. To fit the foot of the bed,
pull from the centre of the blanket to the foot
of the bed, and fit one corner at a time while
holding the centre (see Figure 4). Ensure
the fitted skirt goes completely under the
mattress. Pull on the edges of the blanket
to ensure that it is flat and square on the
mattress.
Connecting the controls
To connect the controls, remove one corner
of the blanket at the head of the bed. Insert
the connector plug into the socket and push
firmly until it clicks into place. Repeat on the
other side if required. Plug the controls into
a 230-240V power outlet and turn the power
on.
Caution: The cord and controls must be kept
outside the bed and away from external
heating sources, such as heaters and lamps.
Do not cover the control.
Fitting your electric blanket
Figure 3.
Figure 4.
Using your electric blanket
9 heat timer control
Your fitted electric blanket is supplied with
a 9 heat timer control. Two controls are
supplied with Double, Queen and King size
electric blankets. The control features an
on/off slide switch to operate the control
plus a choice of three timer settings which
automatically switch the blanket off after
three, six or 12 hours. The illuminated LCD
displays the selected heat and timer settings
(see Figure 6).
Operating your 9 heat timer control
Slide the on/off switch to the ON position.
Select your desired heat setting using the up/
down arrow buttons. Sunbeam recommends
that you only use settings 1, 2, 3 or 4 for all
night use.
Operating the timer
When switched on, the control automatically
defaults to the three hour (3H) timer setting.
To change the timer setting, press the timer
button to scroll through the three options.
Press the timer button once to set the timer
to six hours (6H), press it twice to select the
twelve hour (12H) timer setting. Press the
timer button again to return to the three hour
(3H) setting.
The selected timer setting is displayed on the
LCD, along with the selected heat setting.
You may change the heat setting at any time
during the timer period using the up/down
buttons.
You may change the timer setting at any time
– you do not have to wait for a timer period
to finish before selecting a new timer setting.
Note: pressing the timer button during the
timer period will restart the timer.
For example, pressing the timer button while
the timer is set to three hours (3H) will scroll
to the six hour timer setting (6H) and restart
the timer for six hours.
At the end of the selected time period, the
temperature and timer settings will flash and
the blanket will automatically switch off.
To reset the control after the selected time
period has elapsed simply slide the on/
off switch OFF and then ON again. When
switched on again, the control automatically
defaults to the last temperature and timer
settings selected.
Low, gentle heat for all night use
Medium heat
High heat, for preheating only
1 – 4
5 – 7
8 – 9
Figure 5.
Figure 7.
7
Heading
6
Before first use
Before using your electric blanket for the
first time, we recommend that you switch
your blanket to the maximum heat setting
for two to three hours before bedtime.
This will evaporate the moisture in the
mattress, leaving you with a dry, healthy bed.
Everyday use
With normal bedding, your electric blanket
may require up to two hours of preheating on
the highest setting before bedtime. Sunbeam
recommends that you use only settings 1, 2,
3 or 4 for all-night use.
Using your electric blanket (continued)
Care and cleaning
All Dreamland electric blankets feature
waterproof heating elements, making them
fully immersible and safe to wash by hand
or machine.
Before cleaning your electric blanket, ensure
that the controls are unplugged from the
blanket.
Spot cleaning
Sponge the affected area using a neutral
wool detergent or mild soap flakes mixed with
lukewarm water. Sponge twice with clean
water to remove detergent. Remove excess
water by compressing the wet area between
two towels.
Hand washing
Wash the blanket in lukewarm water with
a neutral wool detergent or mild soap flakes.
Soak for five minutes, then gently squeeze
the soapy water through the fabric.
Rinse thoroughly in clean, lukewarm water
then drain excess water from the blanket.
Do not wring.
Machine washing
Take your electric blanket to a commercial
laundry or wash in a domestic washing
machine (svpermitting). Wash on WOOL
or DELICATES cycle with a neutral wool
detergent or mild soap flakes, below 40°C.
Do not use high speed or extra spin cycles.
Line drying
Drape the blanket across several lines of
your clothesline, and try to avoid direct heat.
Do not use pegs on the wired areas. Do not
dry with a hairdryer or heater. Ensure that the
blanket and control sockets are completely
dry before using again.
Machine drying
Tumble dry your blanket on LOW setting for
15 minutes MAXIMUM. Smooth the blanket
by gently pulling any creases out of the
fabric. Line dry to ensure the blanket and
control sockets are completely dry before use.
Do not dry with a hairdryer or heater.
Storing your blanket
If you wish to remove the blanket from your
bed when not in use, roll or fold it loosely
and store in a blanket bag. Avoid pressing
sharp creases into the blanket.
Do not place heavy items on top of your
electric blanket when storing.
8
Heading
QUICK START
DIGITAL OVEN 22L
User Guide
Need help with your appliance?
Contact our customer service team
or visit our website for information
and tips on getting the most from
your appliance.
Australia | visit www.sunbeam.com.au
phone 1300 881 861
mail Units 5 & 6, 13 Lord Street,
Botany NSW 2019 Australia.
New Zealand | visit www.sunbeam.co.nz
phone 0800 786 232
mail Level 6, Building 5,
Central Park,
660–670 Great South Road,
Greenlane, Auckland.
NEWELL AUSTRALIA PTY LTD. ABN 68 075 071 233
Sunbeam Corporation is a division of GUD Holdings Limited.
Sunbeam is a registered trade mark.
Made in China to Sunbeam’s specification.
Due to minor changes in design or otherwise,
the product you buy may differ slightly from the one shown here.
Approved by the appropriate electrical regulatory authorities.
©Sunbeam Corporation Limited 2020.
05/20
BT7100
Australia
www.sunbeam.com.au
1300 881 861
Suite 1, Level 1,
13 Lord Street,
Botany NSW 2019
Australia
New Zealand
www.sunbeam.co.nz
0800 786 232
Level 6, Building 5,
Central Park,
660-670 Great South Road,
Greenlane, Auckland
New Zealand
Year
3 year
3
Troubleshooting
The electric blanket
is not heating
Check the control is plugged into the electric blanket, and ensure it is clicked
securely into position. If the control connector is not properly fitted to the
blanket, switch the power off at the power outlet, securely attach the control
connector plug to the blanket and then switch the power back on.
Check the power cord is connected to the power outlet and that the power is
switched on.
If you are using a powerboard, check the powerboard is working.
Remember for double, queen and king blankets there are 2 controls. Ensure
both are plugged into the blanket, and both cords are plugged into a power
outlet.
Check the on/off slide switch on the control is switched to ‘on’.
If only one side of the blanket is working, it may simply be because the control
rather than the blanket is not working.
To help resolve your issue quickly, before calling Sunbeam Customer Service,
please check the control. Simply swap the “good controller” to the “faulty” side
of the blanket. Wait 20 minutes to see if the blanket is heating. If it does heat,
the first controller is faulty. If the blanket still does not heat, the blanket may be
faulty. Then call Sunbeam Customer Service line, and they will be able to assist.
The cord or any
wiring is damaged
Do not attempt to repair it yourself. Contact the Sunbeam Customer service line
on 1300 881 861 in Australia or 0800 786 232 in New Zealand.
BLD5021_BLD5031_BLD5041_BLD5051_BLD5071_20EM1 (ANZ)
GCDS-SUN-SL
Need help with your appliance?
Contact our customer service team
or visit our website for information
and tips on getting the most from
your appliance.
Australia | visit www.sunbeam.com.au
phone 1300 881 861
mail Suite 1, Level 1, 13 Lord Street,
Botany NSW 2019 Australia.
New Zealand | visit www.sunbeam.co.nz
phone 0800 786 232
mail Level 6, Building 5,
Central Park,
660–670 Great South Road, Greenlane,
Auckland.
Sunbeam Corporation is a division of Newell Brands.
NEWELL AUSTRALIA PTY LTD. ABN 68 075 071 233
Sunbeam is a registered trade mark.
Made in China to Sunbeam’s specification.
Due to minor changes in design or otherwise,
the product you buy may differ slightly from the one shown here.
Approved by the appropriate electrical regulatory authorities.
©Sunbeam Corporation Limited 2020.
09/20
